what is the cost to rebuild the drive shaft, on a 2002 saturn vue, awd

Almost all front-wheel bulldoze vehicles apply CV axles to transfer engine power from the transaxle to the wheels. An axle seal holds the transmission fluid in at that betoken where the CV axle splines into the transaxle housing. In improver to keeping oil in, the seal keeps the grit and wet out. The seal relies on a tiny amount of lubrication from the fluid it holds in to minimize wearable.

Seal failures are usually due to elementary wear and tear, most oftentimes noticed as fluid leaking out. A leaking beam seal is usually fairly easy to diagnose, being in a place where there aren't often other sources for fluid to leak from.

A very slightly leaking seal that only leaves residue and doesn't affect fluid levels may not be critical to supplant. A leak meaning enough to baste from the housing or leave puddles where the vehicle is parked should probably be addressed sooner rather than later.

Cost of Replacing the Axle Seal

On average, the toll to replace an axle seal is about $150.

For some specific examples of the axle seal leak repair cost in some common vehicles using $100 an hour as a labor rate are equally follows:

• On a 2004 Toyota Corolla, the labor time for a front axle seal replacement (one side) is 2.6 hours and a Beck/Arnley seal costs about $7. Total job price would exist $267.
• On a 2014 Chevrolet Impala, the labor time for a front axle seal replacement is 1.two hours. An OE Air conditioning Delco seal costs most $7. All of these make up for the total toll of around $127.

• On a 2005 Chrysler Pacifica AWD, there is an axle seal on each of the forepart and rear axles. The labor time for each is one.ane hours. An OE beam seal is virtually $25 and an aftermarket SKF seal is almost $13. The axle seal replacement cost in this instance volition be effectually $123 using aftermarket parts or $135 using OE parts.
• The axle seal on the rear of a 2000 Ford Ranger takes i.2 hours of labor fourth dimension. A National seal costs nigh $7; making the job about $127 in full cost.
• On a 1999 Toyota Tacoma, the rear beam seal and bearing must be replaced together. The labor time for that is 1.7 hours, a Timken bearing is near $42, and the two seals needed for a side price nigh $8. Total cost would be $220 all in all.

PRO TIP – If an beam seal is replaced in conjunction with other piece of work that makes it attainable, such as a CV axle replacement, the additional labor for the axle seal is usually about two-tenths of the other labor charges.

Other Expenses That Might Come Up

A part of the procedure for replacing the axle seal is topping off the transmission to replace lost fluid. If the fluid is notably worn or by scheduled service, then, a transmission service would probably exist recommended at the aforementioned fourth dimension.

On rare occasions, a seal may neglect not because of ordinary wear but because the bearing or bushing it protects has failed, allowing excess movement of the beam. Normally, in that case, dissonance or vibration would be noticed. Still, if play in the transmission output shaft is plant, more repairs may be needed.

PRO TIP – I general rule in automotive repair is that whenever a suspension part between the wheels is removed or replaced, checking the alignment is a good thought.

The axles must be removed to replace axle seals. In many cases, this can be done and reassembled without disturbing the alignment. However, this is not always the example and there are often several ways of disassembly to remove an beam depending on unpredictable conditions. If an alignment is recommended by the shop, it'due south probably best to have it washed.

It'southward also a skilful idea if an alignment is non recommended to pay attention to how the vehicle drives after the repairs are done. If the steering wheel has inverse position or any handling issues are noted, very likely an alignment should be done.

How To Repair/Replace Axle Seals?

In forepart-wheel bulldoze vehicles, the metal housing of the seal grips the transaxle instance, and the condom lip of the seal rides on a machined surface of the axle. All-wheel bulldoze vehicles often utilise the same kind of seal on all four axles if they have an independent suspension.

In some cases, the axle isn't splined straight into the transaxle or differential just bolted to a flange that is splined in. Replacing an axle seal is still fairly simple in most cases. It involves removing the axle and the axle flange (if one is used), pulling the seal, installing a new seal, then reassembly.

Rear Beam Seal Replacement

There are a couple different varieties of axle seal on a solid rear axle. The first is as pictured beneath, where the seal is pressed into the tube of the differential, and the axle bearings are correct in backside that. In that organisation it'southward often a skillful idea to replace the axle bearings with the seal, as problems with 1 can lead to problems with the other. In the 2d type the bearings are pressed onto the axle tube and the seal is behind them. In that organisation  the bearings must exist replaced, equally they are inevitably damaged during the removal process to replace the axle seal.

One mutual issue with both of these rear axle seal varieties is that when the seal leaks, it leaks into the braking system because of how information technology is placed. Most often if the braking organisation is contaminated with differential oil information technology is recommended that the brakes should be replaced; adding significantly to the cost. Rotors and drums tin be cleaned, but pads or shoes that have absorbed oil are usually not considered reusable.

The replacement of a rear axle bearing on a solid beam vehicle has no impact on the cycle alignment.

FAQ

How long does it accept to replace a front beam seal?

In most cases a trivial over an hr.

How long tin can I drive with a front axle leak?

Indefinitely, merely the leak may cause the transmission fluid to run likewise depression, which can cause other expensive issues.

Does an axle seal leak crusade other harm?

Generally not, as long as fluid levels are kept upwards. The exception would be a rear axle seal leak, where even a small-scale amount of fluid leaking can impairment the rear brakes.

scottwimen1986.blogspot.com

Source: https://spendonauto.com/axle-seal-replacement-cost/

Share this post